Youtor
>> YOUR LINK HERE: ___ http://youtube.com/watch?v=25xlNzMrLBo
Complete Platinum Toilet Repair Kit Install by Korky | https://www.korky.com/parts/kits/quie... • Hello and Welcome to Korky Toilet Repair. • Today we are going to install your new Korky Complete Platinum Toilet Repair Kit. • The first step is to shut off the water supply to your toilet. • Next flush your toilet. • Mark the water level in the tank with a pencil. • Drain the excess water. • Sponge out the remaining water in your toilet tank. • Place a bucket underneath your toilet tank to catch any excess water. • Disconnect your water supply line and remove the mounting nut. • Remove the old fill valve. • Locate and remove all old nuts, bolts, and washers from the toilet tank. • Carefully lift up on the tank and remove it from the bowl. • Remove the old tank-to-bowl sponge gasket. • Remove the old mounting nut and pull the old flush valve and flapper out of the toilet tank. • Place your new Korky flush valve into the toilet tank, and slide the chipboard washer over the threads. • Hand-tighten the mounting nut. • Place the new red sponge gasket over the mounting nut threads. • Carefully set the tank onto the bowl. • Use the new bolts, rubber washers, washers, and hex nuts, included in the packaging to attach the tank to the bowl. • Apply downward pressure to keep the tank level as you tighten the nuts in an alternating fashion until the tank is stable. • Do not over tighten the nuts; doing so may cause the porcelain to crack. • Next, set the height of the flush valve. • Loosen the locknut and extend the overflow tube until the top of the overflow tube is one inch below the flush lever nut, then hand-tighten the locknut. • Now, turn the top of your new fill valve counter clockwise and pull up to fully extend. • Place the valve in the tank and press down on the fill valve until the corner of the silver cover lines up with the top of the flush valve. • Lock the fill valve in place by twisting the upper half clockwise. • Make sure the rib on the top of the valve lines up with the pegs on the bottom half. • Attach the refill tube to your new fill valve. • Make sure the refill tube has a direct path to the flush valve. • When your fill valve is set, screw on the mounting nut until hand tight. • Push the refill tube towards the front of the tank to ensure the port is locked in place. • Insert the metal clip into the refill tube and attach the clip to the flush valve. • Turn the refill adjuster clockwise to the fully open position. • Then attach the flapper chain to the flush lever with minimal slack. • Reattach the water supply line. • Turn the water supply on and wait for the tank to fill completely. • Turn the water supply off and flush. • If the water drops within a half inch of the pencil mark your flapper installation is finished. • If not, rotate the band to the open position and reinstall the flapper. • Turn the water supply on and let the tank refill completely. • Turn the water supply off and flush. • If your water level is still not within a half inch of the pencil mark, adjust the dial so the next lowest number aligns with the arrow. • Then reinstall your flapper. • Turn the water supply on and let the tank refill completely. • Turn your water supply off and flush. • Repeat this process until the water level drops within a half inch of the pencil mark. • Turn the water supply on and let the tank fill completely. • Flush. • Wait 2 minutes for the water in the bowl to settle, the excess water will drain out. • Mark the water level in the bowl with a pencil or dry erase marker. • Flush. • If the bowl water level reaches the mark before the tank is finished filling, turn the dial counter-clockwise to reduce flow. • If the bowl water level is below the mark once the tank is done filling, turn the dial clockwise to increase flow. • Repeat this step until the water level reaches the pencil mark at the same time the tank finishes filling. • Congratulations, you have successfully installed your new Korky Complete Platinum Toilet Repair Kit. • Thank you for choosing Korky. • If you have any questions or need further assistance with your installation, please visit our website or call us at 1 800 528 3553.
#############################
