Youtor
6X12 VNose Cargo Trailer Conversion for 4
>> YOUR LINK HERE: ___ http://youtube.com/watch?v=3lHATY1Y2lQ
This is a full assemble video on how to build a 3D printed RC Tucano. Below is a link to all the parts and materials. Also I have all my surface layer 3 setting listed bellow. 2200grams RTF with 4S 4000 man battery. • Thank you so much for watching! • If you like videos like this, consider buying me a coffee, it really supports me: • https://www.buymeacoffee.com/troymcmi... • See what else I am working on: / troymcmillan_rc • https://www.tiktok.com/@troymcmillan_... • #3DPrinted,#RCAirplane, #ItFlies • Thank you so much to https://www.planeprint.com for sponsoring this build! • How to Print Thin Wall: • How to Print Thin Wall - Planeprint |... • Maiden Flight: • Maiden Flight RC 3D Printed Tucano - ... • Products Mentioned: • Super Tucano STL: https://www.planeprint.com/product-pa... • JGAurora A5S 3D Printer: https://amzn.to/3hn5cdN • JGMAKER MAGIC Printer: https://amzn.to/3nmonb6 • Black PLA: https://amzn.to/3gMxS0a • White PLA: https://amzn.to/3ghcHl1 • TPU: https://amzn.to/2Sw3Oe8 • CA Glue: https://amzn.to/2J8EvNW • CA Accelerator: https://amzn.to/3fpbycz • 5x HS-55 Servos: https://amzn.to/3oRnDKV • 3548 1100KV Motor: https://amzn.to/3qXf3wg • 60amp ESC: https://amzn.to/3nwXJw1 • 12x6 Propeller: https://amzn.to/2Knji3e • 4S 4000mAh Battery: https://amzn.to/37fulV7 • AR620 Receiver: https://amzn.to/3j4PbK4 • DX6 Transmitter: https://amzn.to/3l6NFsD • 3pin wire assortment: https://amzn.to/3l1xNYt • XT60 connector: https://amzn.to/3iyZWnf • 5mm magnet: https://amzn.to/35ZPLoN • Screw assortment: https://amzn.to/2SvMxSs • 2mm push rod ends: https://amzn.to/3nnjD4U • Z-Bend pliers: https://amzn.to/34mA0rt • Hot knife: https://amzn.to/34AGOB1 • Drill Bits: https://amzn.to/3nIJzrx • Carbon Rods: https://www.readymaderc.com • • • • *These are the settings I used for my JG A5S 3D Printer with Black Esun PLA. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck! • Profile 3 Cura Settings: • Quality: • Layer Height – 0.25 • Line Width – 0.4 • Shell: • Wall Line Count – 1 • Infill: • Infill Density – 0 • Material: • Printing Temperature – 215 • Build Plate Temperature – 60 • Flow – 100 • Speed: • Print Speed – 100 • Outer Wall Speed – 40 • Inner Wall Speed – 40 • Travel Speed – 100 • Travel: • Enable Retraction – Checked • Retraction Distance – 4 • Retraction Speed – 70 • Retraction Extra Prime Amount – 0.7 • Combing Mode – off • Cooling: • Enable Print Cooling – Checked • Fan Speed – 20 • Mesh Fixes: • Union Overlapping Volumes – NOT Checked • Special Modes: • Surface Mode – Surface • Experimental: • Slicing Tolerance – Middle • • • • Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!tor and propeller setup I used. I will show how I fixed the problem and take it out for another flight.
#############################
