Youtor
M601 M602 M603 Fuser amp Maintenance Kit Replacement Instructions part number CF06467901
>> YOUR LINK HERE: ___ http://youtube.com/watch?v=NRpSTyJkYr0
Today we will be reviewing the removal and installation process for the HP HP M601 M602 M603 Fuser Maintenance Kit Replacement Instructions part number CF064-67901 • Start by making sure the printer is off for at least 15 minutes and unplugged. Approach the printer from the front and open the tray door. • Suggested Tools • Flat head screwdriver • Magnetic tip phillips head • Kit Contents: • Kit Contents: • 1 Transfer Roller: RM1-0699 • 4 Feed/Separation: Rollers RM1-0037 • 2 Pickup Rollers: RM1-0036 • 1 Fusing Assembly: RM1-8395 • Repair Notes • The Page count Reset instructions will be located in the comments of the video or blog page so check below. • 220,000 page yield • This fuser and kit is available at in an number of different options at metrofuser • Thanks for watching. If you would like to see more of these videos hit like and subscribe..Visit on Metrofuser's Youtube channel or http://www.metrofuser.com • HP M601 M602 M603 Maintenance Kit Replacement Instructions • This printer maintenance kit provides you with the most commonly used parts that wear. Replacing these worn parts will allow for maximum paper feed along with quality print performance. • Specifications: • Expected Duty Life: 200,000 pages • Kit Part Number: CF064-67901 • ------------ WARNING: Printer Parts May Be Hot ------------- • Turn the printer off, unplug it, and allow it to sit for 30 minutes before • performing these maintenance procedures. • Transfer Roller Removal and Replacement • 1. Open toner access door and tray 1. • 2. Remove toner cartridge. • 3. Lift the gear (left side) of the transfer roller up. • 4. Slide to the left and remove. • 5. Slide right side of replacement roller into right bushing. • 6. Align left side collar making sure the open end is face down and push in. • CAUTION: Do not touch the surface of the transfer roller. Contact with skin can cause print quality problems.. • Tray 2 Feed and Separation Roller Removal and Replacement • 1. Remove the tray from the printer. • 2. On the tray, lift the roller cover next to the roller. • 3. Pinch the blue tab and slide the roller off the shaft. • 4. Slide new roller on making sure the tab locks. • 5. Locate the feed roller in the top of the tray cavity. • 6. Repeat steps 3 and 4. • NOTE: The removal and replacement process are the same for the feed and separation rollers on tray 3 and the 1500 • sheet feeder. • Fusing Assembly Removal and Replacement • 1. Open rear output bin/face up tray. • 2. Remove output bin from printer. • a.) Locate the left side hinge pin (there is a finger notch) squeeze the left hinge pin to the right to • release it from its mounting hole. • 3. Slide the output bin to the left to remove from printer. • 4. Pinch the blue tabs on the fuser and pull fuser out of printer. • 5. Push the new fuser into the printer making sure both blue tabs lock. • 6. Install the rear output bin/face up tray and check for proper operation. • Resetting the Maintenance Count • 1. At the control panel, press the Home () button. • 2. Use the down arrow button () to select ‘ADMINISTRATION’ then press the OK button. • 3. Use the down arrow button to select ‘MANAGE SUPPLIES’ then press the OK button. • 4. Use the down arrow button to select ‘RESET SUPPLIES’ then press the OK button. • 5. Use the down arrow button to select ‘NEW MAINTENANCE KIT’ then press the OK button. • 6. Use the down arrow button to select ‘YES’ then press the OK button. • 7. The display should show ‘SETTINGS WERE SAVED SUCCESSFULLY’. • 8. Print a configuration page. Ensure the ‘Pages since last maintenance’ entry is set to zero.
#############################
