35KW Briggs amp Stratton Standby Generator Installation

>> YOUR LINK HERE: ___ http://youtube.com/watch?v=ZfQxptYsk0w

Briggs Stratton Model# 76140 - 35 kW Liquid Cooled Standby Generator Installation. Read All of the Text Below for Common Generator Replacement Part Numbers : • Briggs Stratton 071054 - Symphony Transfer Switch and If necessary to Have Cutoff In Transfer Switch- 6308 Kit. • Briggs Stratton 6241-0 - Engine Coolant Heater Kit • Mounting L Brackets - Thomas Betts Item# ZAB205-10 • Battery – Costco# 850259 – Interstate Group# 65 Fitment Code #4 • Generator Parts with OEM Information: • Engine is a GM 4 Cylinder 3.0L Vortec Engine - 2015 - Impco Model# 7044600 • Oil - Pennzoil 550038331 Ultra Platinum 10W-30 Full Synthetic Motor Oil • Oil Filter is - PF 1218 (a longer version of the stock one) • Spark Plugs # R42LTS Gapped at .035 - OEM Part# 19301658 • Alternator V- belt - Goodyear Gatorback 15386 - 11AV0965 or Briggs Part# 314138GS - Continental Elite V-belts Part# 20033481 • Radiator Hoses: • Upper Hose: Dayco 81171 - or Briggs Part# 313211GS • Lower Hose: Dayco 81351 - or Briggs Part# 313210GS • Air Cartridge Filter - Donaldson P532410 - or Briggs Part# 207575GS • Distributor - GM Part# 93442429 Impco Part# 93442429 • Rotor - GM Part# 10467546 Impco Part# 7241620 • Wiring For Generator: http://www.wireandcabletogo.com • A. Power Cable – Item# VNT2s0-3C-G - #2/0-3C THHN-PVC TrayCable w/G • B. 2 x 120V Cable - Item# VNT12-2C- #12-2C THHN-PVC Tray Cable • C. Communication wire– Item# -VNT18-6CS - #18-6C THHN-PVC Shielded Tray Cable • American Fittings Corp. STR-250 CG125D1150 Liquid-Tite Flexible Conduit • Other Generator Part Numbers: • Thermostat – Impco# 7140340 - B S #314093 • Gasket Thermostat – Impco# 7140310 - B S #314091, GM #10105135 • Ignition Coil – Impco# 7242320 - GM #1115491 • Spark Plug Wire Set - Impco# 7241830 - B S # 314126 - GM # 93430078 • Alternator, Impco# 7SI – 7244700 - B S# 314137, GM # 19020608 • PCV - Impco# V3-51806-001 - B S # 314143, GM # 8995284 • Starter Motor (includes items 4-7 12) - Impco# 821042 - Landoll Corp. Described as: Starter, 2kW PG260N2 • Crank Sensor – IMPCO# S8-51822-001 and GM Part# 12588992 • Oxygen Sensor in Exhaust – Briggs Part# 314122GS. The Part Says on it that • It is a Model# 0258006956, I believe it's made by Bosch. • Impco Catalog# 1 HEGO 1, Pre-Catalyst 1 7176700 • You need a 7/8 Inch Wrench and have to Slip the closed side over the wire by unclipping the wired side and sliding it down the wire until it’s over the bolt on the sensor. Be sure to add lots of anti-seize to the threads and tighten lightly. Do Not use Silicone spray, it will damage the sensor. • Second Oxygen Sensor TMAP in Air Intake: • Briggs Part# 314107GS • Impco Manual says: HEGO 2, Post Catalyst 1 - S8-50234-001 • • Water Port Pieces: • Adapter, Freeze Plug O-ring - Impco# A4-51798-001 - B S# 314145 • Clip, Retaining - Impco# P1-30559 - B S# 314146 • Fitting, 5/8 x 90 x .78” - Impco# AF4-50733-001 - B S# 314147 • Fluids: • Coolant - 50/50 Mix - 4 Gallons • Oil - 10W30 Synthetic 4.3 Quarts

#############################

New on site