Neptune 4 Max load screen and software error fix

>> YOUR LINK HERE: ___ http://youtube.com/watch?v=b2Od4YHcLAQ

Using the best entry level 3D Printer the Creality Ender3 I will show you step by step how to start your first print, level the bed and tell you all about the different filaments there are for your printer. • Propeller Wall Art: https://cults3d.com/en/3d-model/art/p... • 0:00 3D Printing Basics Intro • 1:30 How to Assemble a New Ender 3 • 2:32 How to adjust Ender 3 belts • 3:08 Different types of 3D printing filament • 5:16 What is the difference between an STL and a GCODE? • 6:53 How to install Cura? • 8:09 How to download a free STL file from Thingiverse? • 9:17 Why is my part greyed out on Cura? • 11:00 How to level a 3D printer bed? • 13:20 How to load new filament into a 3D printer? • 14:43 Best bed adhesion method for 3D printing? • 16:10 How to get a good first layer with 3D printing? • 19:29 How to set up a stringing test for a 3D Printer? • 21:28 Ender 3 Retraction settings • 21:43 How to set up Planeprint test part • 24:09 How to set up TPU on a 3D printer? • Spool Holder STL: https://cults3d.com/en/3d-model/tool/... • Links to purchase printer: • Creality 3D Ender 3 V2: https://amzn.to/3PQyVNZ • Thank you so much for watching! • If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi... • See what else I am working on: / troymcmillan_rc • / troymcmillan_rc • #3DPrinted,#RCAirplane, #ItFlies • Airplane STL files: • https://www.planeprint.com • https://www.eclipson-airplanes.com • https://3dlabprint.com • https://www.3daeroventures.com • https://3d-printz.at • Basic supplies: • Spektrum DX6 Controller: https://amzn.to/3m21tGz • Spektrum NX10 Controller: https://amzn.to/3jnjvST • Receiver: https://amzn.to/3j4PbK4 • Battery Charger: https://amzn.to/3M5EVzj • CA Glue: https://amzn.to/2J8EvNW • Onboard Camera: https://amzn.to/3rp2OrH • Soldering Iron: https://amzn.to/3NCsLiy • • --------Print Settings----------- • *These are the settings I used for my Creality Ender 3 V2 3D Printer with PLA. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck! • ---------Pliers • STL:https://www.thingiverse.com/thing:291... • Cura Settings: • Quality: • Layer Height – 0.16 • Line Width – 0.4 • Walls: • Wall Line Count – 3 • Top/Bottom: • Top Layers: 4 • Bottom Layers: 4 • Infill: • Infill Density – 20 • Infill Pattern - Grid • Material: • Printing Temperature – 215 • Build Plate Temperature – 60 • Flow – 100 • Speed: • Print Speed – 100 • Outer Wall Speed – 50 • Inner Wall Speed – 50 • Travel Speed – 100 • Travel: • Enable Retraction – Checked • Retraction Distance – 7.5 • Retraction Speed – 35 • Retraction Extra Prime Amount – 0 • Combing Mode – all • Avoid Printed Parts When Traveling - NOT Checked • Cooling: • Enable Print Cooling – Checked • Fan Speed – 100 • Mesh Fixes: • Union Overlapping Volumes – Checked • Special Modes: • Surface Mode – Normal • Experimental: • Slicing Tolerance – Middle • • ---------Planeprint Profile 3 • Test Wing STL: https://www.planeprint.com/print • Cura Settings: • Quality: • Layer Height – 0.25 • Line Width – 0.4 • Walls: • Wall Line Count – 1 • Top/Bottom: • Top Layers: 0 • Bottom Layers: 0 • Infill: • Infill Density – 0 • Material: • Printing Temperature – 215 • Build Plate Temperature – 60 • Flow – 100 • Speed: • Print Speed – 100 • Outer Wall Speed – 50 • Inner Wall Speed – 50 • Travel Speed – 100 • Travel: • Enable Retraction – Checked • Retraction Distance – 7.5 • Retraction Speed – 35 • Retraction Extra Prime Amount – 0 • Combing Mode – all • Avoid Printed Parts When Traveling - NOT Checked • Cooling: • Enable Print Cooling – Checked • Fan Speed – 30 • Mesh Fixes: • Union Overlapping Volumes – NOT Checked • Special Modes: • Surface Mode – Surface • Experimental: • Slicing Tolerance – Middle • • -------TPU Settings • Cura Settings: • Quality: • Layer Height – 0.25 • Line Width – 0.4 • Walls: • Wall Line Count – 2 • Top/Bottom: • Top Layers: 4 • Bottom Layers: 4 • Infill: • Infill Density – 10 • Infill Pattern - Grid • Material: • Printing Temperature – 210 • Build Plate Temperature – 60 • Flow – 100 • Speed: • Print Speed – 100 • Outer Wall Speed – 20 • Inner Wall Speed – 20 • Travel Speed – 100 • Travel: • Enable Retraction – Checked • Retraction Distance – 7.5 • Retraction Speed – 35 • Retraction Extra Prime Amount – 0 • Combing Mode – all • Avoid Printed Parts When Traveling - NOT Checked • Cooling: • Enable Print Cooling – Checked • Fan Speed – 100 • Mesh Fixes: • Union Overlapping Volumes – Checked • Special Modes: • Surface Mode – Normal • Experimental: • Slicing Tolerance – Middle • • • • • • • Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!

#############################

New on site