How to Build a Nightstand with Drawer FROM PLYWOOD amp 2x2s

>> YOUR LINK HERE: ___ http://youtube.com/watch?v=cqss8A1C_RQ

Hey friends, let's build a modern nightstand to match the storage bed I shared in my last video! • This video was sponsored by Shopify. Start your free trial today at https://www.shopify.com/woodshopdiaries/ • This simple nightstand design could easily be used as an end table, too. It's a great DIY woodworking project for the weekend as it only takes a few hours to put together. • Check out additional tips, details, and information on the build here: https://www.woodshopdiaries.com/how-t... • Grab the printable plans for this project build here: https://woodshop-diaries.myshopify.co... • Wood Type: I built this from red oak--both solid wood and red oak plywood. However, any wood type would work fine for this. Construction lumber (pine/spruce/fir) and birch plywood are what I normally use most and are a great budget friendly option if you didn't want to splurge on oak! • Check out the matching bed build here: • How to Build a Storage Bed with Built... • *Follow Woodshop Diaries On* • Website: https://www.woodshopdiaries.com/ • TikTok: / woodshopdiaries • Facebook: / woodshopdiaries • Instagram: / woodshopdiaries • Pinterest: / sharamccuiston • SHOP WOODWORKING TEES AND BUILDING PLANS HERE: • https://woodshop-diaries.myshopify.com/ • *Helpful resources for this build:* • How to cut your own 2x2s: https://www.woodshopdiaries.com/woodw... • How to cut plywood sheets: https://www.woodshopdiaries.com/cut-d... • How to apply edge banding: https://www.woodshopdiaries.com/how-t... • How to use a pocket hole jig: https://www.woodshopdiaries.com/how-t... • How to use a dowel jig: https://www.woodshopdiaries.com/how-t... • How to install drawer slides: https://www.woodshopdiaries.com/how-t... • How to build a drawer box: https://www.woodshopdiaries.com/how-t... • How to attach a drawer front: https://www.woodshopdiaries.com/how-t... • Tools Materials: • *Affiliate links below • Tools: • Drill/Driver: https://homedepot.sjv.io/Aoo6Ya • Circular Saw: https://homedepot.sjv.io/AooaYx • Cutting Guides: Kreg Rip Cut: https://amzn.to/3Y38tDQ Kreg AccuCut: https://amzn.to/49jZFAe • Pocket Hole Jig: https://amzn.to/32eoPBY • Dowel Jig (optional): https://amzn.to/3sNQ83O • Miter Saw: https://homedepot.sjv.io/b3DkDx • Clamps • Table Saw (optional) • Kreg Drawer Front Installation Jig: https://amzn.to/3SbKYr8 • Materials: (materials list is for ONE nightstand) • (1) 4’x8′ sheet ¾″ plywood • (1) 2’x4′ (¼ sheet) ¼″ plywood • (2) 2x2x8 boards • 1 ¼” pocket hole screws: https://amzn.to/3FKfikk • 2 ½” pocket hole screws: https://amzn.to/3RJrA5y • OR 1 ½” dowel pins: https://amzn.to/3urFKPD • 2” wood screws • Wood glue: https://amzn.to/34NCtuv • Edge banding (optional): https://amzn.to/3nx64RT • (1) pair 14″ drawer slides: https://amzn.to/3v65BNk • Drawer Pulls/Knobs: https://amzn.to/4aeXEWt • Chapters: • 00:00 Introduction • 00:35 Assembling Nightstand Frames • 03:36 Installing the Side Panels • 05:13 Adding the Shelves • 07:34 Adding the Drawer • 10:00 Attaching the Top • 11:07 Finishing the Nightstands • 11:40 Final Reveal

#############################

New on site