Sikkens Cetol HLS Plus Sikkens HLS Plus Low Build Basecoat and Wood Stain

YOUR LINK HERE:

http://youtube.com/watch?v=fwLWnwRjHdQ

Sikkens cetol HLS Plus is a low build satin basecoat and wood stain for most exterior woods. It can be used as both a basecoat and a finishing coat depending on the project you are doing. • https://www.wood-finishes-direct.com/... • It is resistant to UV, surface mould and algea, peeling and cracking. The wood grain remain visible and it can be over coated with Sikkens Cetol Filter 7 Plus. • It is an ideal product to use on softwood, hardwood ,plywood, block board and partical board, such as cladding, fascias, archatraves, timber frames, fences, and sheds. • Preparation • Wood to be treated with Sikkens Cetol HLS Plus should be clean, dry and free from surface dirt, debris and surface coatings such as paint or varnish. • Degrease any exposed bare timber surface by wiping with a cloth dampened in a suitable solvent. • The use of 'knotting agents' is not recommended with translucent finishes as they are not always fully effective in sealing in resin, the presence of knots is often highlighted and adhesion of coatings can be impaired. • When filling, be sure to use fillers specifically designed for use with timber. General or all purpose fillers may not be suitable. • Applying Sikkens HLS Plus • Always do a test area before starting any project to test adhesion and final finish. Follow the manufacturer's instructions on the tin at all times. • Ensure that Sikkens Cetol HLS Plus is stirred thoroughly before and periodically during application use to ensure a consistent finish. • Application temperature should not be below or exceed 5 - 30℃ and a relative humidity of 85%. • New timber • Where a superficial application of wood preservative to softwood and hardwood is deemed necessary, ensure that the wood preserver used does not contain any wax and has fully dried before applying Cetol HLS plus. • Note: Sikkens Cetol HLS Plus cannot be used on substrates which have had water-repellent wood preservative or pre-treatments applied i.e. products that contain wax, oil or silicon. • Where possible, the first coat should be applied all round prior to fixing. Only use non-ferrous screws, nails and fixings. Denib using a fine grade nylon abrasive pad or a fine grade (P240 or finer) wet or dry silicon carbide abrasive paper, in the direction of the grain. Do not break through the surface coating. Take care to ensure that all sanding / denibbing dust has been removed from the surface prior to applying additional coats. • Note: Where any damage, or deterioration has occurred as a result of exposure of the factory coating for longer than 3 months, affected areas should be thoroughly sanded back to a sound substrate. • Damaged or decayed timber • All damaged or decayed timber must be removed and replaced, cutting at least 25mm into sound timber. When splicing in new sections of timber, consideration should be given to the use of a timber species whose natural durability is sufficient. Brush apply two coats of a suitable wax free wood preserver. Ensure timbers are thoroughly treated, especially any end grain sections, and are fully dry before splicing in. Secure with non-ferrous fixings and fill all voids surrounding the spliced-in area with a suitable exterior wood filler. • Apply 2 finishing coats of Sikkens HLS plus. For best results, it is necessary to keep the interval between applications of these coats limited, not exceeding 1 month. • Depending on the condition of the finish, clean, degrease and sand thoroughly. Repair defects with Cetol HLS plus in the appropriate colour and apply one full coat of Cetol HLS plus, overall. Transparency Maintain the translucent appearance of Cetol HLS plus over a longer period. It is recommended to use Cetol Clearcoat LB or alternatively use lighter colours, 077 or 006 for maintenance applications. • Product Coverage • Coverage greatly depends on the wood species under treatment, the surface condition, the method of application and conditions during application. Under normal conditions, coverage will be between 10 to 14 square meters, On rough sawn timber the coverage is significantly lower (e.g. 7 - 10 square meters). • Equipment Cleaning • Application brushes and equipment should be cleaned immediately after use with White Spirit. • Storage • Keep this product tightly sealed at all times and stored / transported in an upright position. Store in a dry place at temperatures between 5 - 30℃. Shelf life for this product is a minimum 24 months in original and unopened packaging. • Drying Time • Sikkens HLS Plus is touch dry after 4 to 6 hours and recoatable between 18 to 24 hours. Air temperature and humidity may affect drying times. • For more information and buying options, visit Wood Finishes Direct • https://www.wood-finishes-direct.com/...

#############################

New on site