Youtor
ShotKam Setup Instructions Attaching User Modes and Calibration Made Easy
>> YOUR LINK HERE: ___ http://youtube.com/watch?v=hp9dnHcNA2c
Welcome to this step-by-step guide on how to attach the ShotKam to your gun, easily navigate through its various modes, and calibrating it to ensure accurate results (read more). • Step 1: Mounting ShotKam • ・ Begin by locating the silver screw provided with the ShotKam and use the allen key to loosen it. • ・Carefully position the ShotKam onto your gun, making sure the USB port is closest to the barrel. • ・Once the ShotKam is in place, tighten the silver screw with about 5 pounds of pressure. Be cautious not to overtighten, as it may cause damage. • ・Optimal positioning of the ShotKam is crucial for the best video recording. Attach the ShotKam about 3 to 8 inches back from the muzzle. Find a balance that feels comfortable for your gun and minimizes any barrel visibility in the video. • Step 2: User Modes • ・To begin using your ShotKam, make sure it is powered off. • ・To activate Normal Shooting Mode, press the power button with one quick click. A solid green light will indicate that the mode is active. • ・In Normal Shooting Mode, the ShotKam records at the highest frame rate and automatically enters Sleep Mode after 20 seconds of inactivity to conserve battery. When in Sleep Mode, the green light will flash. You can wake it up by either closing the shotgun action or clicking the control button for a solid green light. • ・After taking a shot, a blue light will appear following the recoil, indicating that the video has been saved. • ・For continuous recording without pressing the power button, use the Constant Record mode. Start with the ShotKam off, and then double click the power button quickly. You'll see one green and one blue LED, indicating that it's constantly recording. This mode can last up to two hours. To stop the video, click the control button until it turns solid green. • Step 3: Reviewing Videos and Calibration • ・When you're ready to review your recorded videos in the field, turn off the ShotKam. • ・To activate the WiFi signal, hold down the power button for three seconds. Two LED lights will come on, and after a few seconds, one will turn green, indicating that the ShotKam is now sending out its own WiFi signal. • ・On your smartphone, iPad, or tablet, connect to the ShotKam WiFi through your settings. • ・Open the ShotKam App and effortlessly download all your recorded videos for review and analysis. • ・To calibrate your reticle (red dot or crosshair) to the bead of your gun, turn the ShotKam into WiFi Mode by holding down the control button for three seconds. • ・Access your phone settings, tap on WiFi, and connect to the ShotKam network. • ・Open the ShotKam App, click on Calibrate Device, and point your gun at a target about 30 meters away or beyond. • ・Use the arrows in the app to adjust the reticle until it accurately matches the gun's aiming position. • ・Click Save, exit the app, and your ShotKam is now perfectly calibrated and ready for action. • Conclusion • You've successfully learned how to attach the ShotKam to your gun, navigate through its user modes, and calibrate it for precise shooting analysis. The ShotKam is a fantastic tool for capturing and reviewing your shooting experiences, allowing you to continuously improve and refine your skills. With this step-by-step guide, you can make the most of your shooting sessions and take your performance to new heights. So, grab your ShotKam and gear up for a thrilling shooting adventure! Happy shooting! • 00:00 Introduction • 00:11 Mounting ShotKam • 00:44 User Modes • 02:31 Calibrating ShotKam • ShotKam Gen 4 is a durable and weatherproof 4K video camera that mounts to your gun barrel. Designed as a training tool, the movements of your gun are revealed by the red dot or crosshair in the video. • Buy now: https://shotkam.com • Contact us: [email protected]
#############################
